Enerzone Euromax Manuale del Proprietario

SAFETY PRECAUTIONS 1 OWNER’S MANUAL • Warning: If your appliance is

1.5. ANCHOR THE STOVE The stove must be anchored to the floor with screws. Please use the two holes located on each side of the pedestal (see f

1.6. VENTING In Canada, we recommend that you use a listed pellet vent that meets the ULC S-609-M89/ORD C441-M90 Standard. For the United State

1.6.2. Installation Configurations Termination Location Termination should not be located so that hot exhaust gases can be a hazard. They can rea

United States: • Not Less than 36’’ (91 cm) above any forced air inlet located within 10 feet (305 cm); • Not Less than 48’’ (122 cm) below and h

b) Horizontally through wall (Refer to figures 11 or 12) NOTE: Follow Vent chimney manufacturer’s instructions. 1. Position stove, adhering to

FIGURE 13Venting through roof

c) Vertically into existing chimney system (Refer to Figure 14) As an alternative, 4” vent can be run inside existing chimney to termination (Fig

e) Installation through side of masonry chimney (Refer to figure 16) NOTE: Follow vent chimney manufacturer’s instructions. 1. Position the stove

2. OPERATION 2.1. PROPER FUEL THIS STOVE IS APPROVED FOR BURNING four different types of pellets: standard wood pellets, 100% bark pellets, sawdu

2.3.1 LCD User Interface – Operation and Configuration The LCD interface used on the Enerzone Euromax is a touch screen, an electronic visual d

SAFETY PRECAUTIONS 2 INTRODUCTION Thank you for purchasing the EUROMAX pellet stove. You are now prepared to burn pellet in the most efficient, c

Here is a brief description of each bottom: = Indicates that the stove status is on manual mode , = Indicates that the stove status is on therm

2.4. OPERATION TREE 2.5. SELECTING LANGUAGE You can choose between English and French. In order to change the language, refer to the operation

2.9. CHOOSING THE PILOT LAG TIME It is possible to change the setting of your unit such that if the thermostat does not call for heat after 45 min

• If you are using a wireless wall thermostat or a hand held thermostatic remote control, you can locate the receiver behind the stove’s back panel

2.14. FILLING-UP THE AUGER When the stove runs out of pellets, it empties the auger housing. In order to start the stove again, you need to fill

2.17. STARTING THE STOVE Before you start your stove, fill hopper and clean burn pot. Once the hopper is full of pellets, the auger is filled, and

c. WARNING: DO NOT OVERFIRE THIS STOVE. This may cause serious damage to your stove and void your warranty. It also may create a fire hazard in yo

3. MAINTENANCE FAILURE TO CLEAN AND MAINTAIN THIS UNIT AS INDICATED CAN RESULT IN POOR PERFORMANCE AND SAFETY HAZARDS. NEVER CLEAN WHEN HOT. WARNI

3.2. MAINTENANCE OF THE COMBUSTION CHAMBER, HEAT EXCHANGERS AND BLOWER HOUSING Remove and clean the baffle inside the combustion chamber after bur

3.4. VENTING SYSTEM MAINTENANCE REGULARLY EXAMINE THE FLUE PIPES, THE JOINTS, AND THE SEALING TRIMS TO ENSURE THAT THE SMOKE AND THE COMBUSTIO

SAFETY PRECAUTIONS 3 SAFETY PRECAUTIONS • DO NOT OPERATE YOUR STOVE IF YOU SMELL SMOKE COMING FROM IT. TURN IT OFF, MONITOR IT, AND CALL YOUR DE

CAUTION: CLEANOUT OF THE HEAT EXCHANGER, FLUE PIPE, AND CHIMNEY, IS ESPECIALLY IMPORTANT AT THE END OF THE HEATING SEASON TO MINIMIZE CORROSION DUR

3.6. DOOR ADJUSTMENT In order for your stove to operate properly, the door should be adjusted periodically to provide an air tight fit. To adjust:

3.8. GLASS CARE Clean door glass as necessary. The use of a specially designed cleaner is recommended. Your authorized Enerzone dealer can also a

In the handle area, apply the gasket in surrounding the cast iron extrusion to ensure an adequate airtightness. Cut the gasket using cutting plie

9. Set the torx of the power driver at 1/3 of its capacity. Install the retainers using the screws removed in step 2. Start by installing one scr

3.10. REMOVAL AND REPLACEMENT OF GASKETS EXHAUST BLOWER CLEANOUT TRAP GASKET Step 1: Open the rear door located to the left of the appliance. Re

Step 3: Apply gasket #21344 from AC09190 on the exhaust blower cleanout trap and secure it all with all 6 bolts kept on step 2. Close the rear door

Step 2: Remove all 8 bolts securing the clean out trap. Remove the worn gasket and clean-up the contact surfaces. Clean-up the dirty area inside the

Step 4: Put back in place the side air jacket access panel and re-attach all 9 spring clips. Put back in place the front side panel located to the l

Step 2: Remove all 6 bolts retaining the right clean out panel. Remove the worn gasket and clean-up the contact surfaces. Clean-up the dirty area in

SAFETY PRECAUTIONS 4 • ALLOW THE STOVE TO COOL BEFORE CARRYING OUT ANY MAINTENANCE OR CLEANING. ASHES MUST BE DISPOSED IN A METAL CONTAINER WITH A

3.11. RECOMMENDED MAINTENANCE SCHEDULE Use this as a guide under average-use conditions. Components Weekly or after +/- 500 pounds Twice a yearor

4. TROUBLESHOOTING GUIDE When your stove acts up, your first reaction may be to call for help.This guide may save time and money by enabling you to

Possible Causes: Possible Remedies: (Unplug stove first when possible) 1. The hopper is out of pellets. Refill the hopper. 2. The burn pot hol

Possible Causes: Possible Remedies: 1. Blockage in igniter tube or inlet for igniter tube. Remove the burn pot and clean it thoroughly. Make sure

Possible Causes: Possible Remedies: 1. The auger jammed, the auger motor is defective or the wiring harness shorted. Remove the control board cov

Possible Causes: Possible Remedies: 1. The hopper lid has stayed open for more than 3 minutes As a security measure, the auger stops t

• GLASS “SOOTS” UP AT A VERY FAST RATE • FLAME IS LAZY, DARK, AND HAS BLACK TIPS • AFTER STOVE HAS BEEN ON FOR A WHILE, THE BURNPOT OVERFILLS Pos

5. ELECTRICAL DIAGRAM FIGURE 31

5.1 FUSE ACCESS: All fuses are located inside the pc boa

49 6. REPLACEMENT PARTS Contact an Authorized ENERZONE Dealer to obtain any of these parts. Never use substitute materials. Use of non-approved

TABLE OF CONTENTS SAFETY PRECAUTIONS ...

50 # ITEM PART # QTY47 BLOWER ANTI-VIBRATION CUSHION 30335 448 RIGHT BLOWER MOUNT PL62359 249 BLOWER (500 CFM, 115v, 60Hz, 1100 RPM) 44108

51

52 APPENDIX A HORIZONTAL AND VERTICAL VENT CHART For example, let’s imagine an installation consisting of a horizontal vent coming o

53 APPENDIX B INSPECTION FORM

54 APPENDIX C LCD INTERFACE MOUNTING Step 1 The LCD mounting bracket is located in the hopper of the appliance and is preassembled to be install

55 Step 3 Take the Telco black wire (D) which is located in the middle of the rear bottom panel and plug it into the back of the LCD touch screen

56 ENERZONE LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. Th

3.10. REMOVAL AND REPLACEMENT OF GASKETS ... 35 3.11. RECOMMENDED M

1. INSTALLATION 1.1. FEATURES ENERZONE EUROMAX FREESTANDING PELLET STOVE • Width: 24” • Height: 41” • Depth: 28” • Weight: 375 lbs. • Flu

falling through to the combustible floor if cracks or separation should occur in the finished surface, this would include floor protection for built

1.4. COMBUSTION AIR SUPPLY It is mandatory to connect this stove to an outside combustion air source to reduce the risk of hopper burn back caused