Enerzone Solution 2.0 Specifiche Pagina 1

45285 ENERZONE WOOD STOVE MANUAL MODEL SOLUTION 3.4 US ENVIRONMENTAL PROTECTION AGENCY PHASE II CERTIFIED WOOD STOVE STOVE BUILDER INTER

9 Graphic 1 A- Clearance to combustible material with no protection. B- 500 mm (20 po.) minimum; C- 25 mm (1 po.) minimum; D- Between 25 mm

10 Graphic 2 A- 25 mm (1 po.) minimum; 1- Combustible wall ; 2- Non-combustible spacer; 3- 0.61 mm (0.024") sheet metal. Graphic 3 A- 25 m

11 Graphic 5 A- 25 mm (1 po.) minimum; 1- Combustible wall; 2- Non-combustible spacer; 3- Brick. Graphic 6 A- 25 mm (1 po.) minimum; 1- Com

121.4 FLOOR PROTECTOR If the stove is to be installed on top of a combustible floor, it must be guarded by a non-combustible material extending at l

13SECTION 2.0 CHIMNEY (FLUE SYSTEM) 2.1 DEFINITIONS For clarity, the following definitions should be used with respect to these instructions: •

14USA the ANSI NFPA 70 and ANSI NFPA 211 installation codes are to be followed. If you are using a masonry chimney, it is important that it be built

15 FIGURE 2.2 Minimum Height of the Chimney 2.2.1 Step by step installation of your factory-built chimney The way to install your chimney may v

16Stove pipe • An adequate number of stove pipe sections. • A 90o elbow FIGURE 2.2.1 (A) Typical installation through the wall

17Typical installation through the ceiling Ceiling support system If your chimney must rise inside the house and go through the ceiling, you need t

18 2.2.2 Typical installation through an existing masonry chimney You can also install your stove using your existing masonry chimney. To do so, f

1INTRODUCTION Stove Builder International, one of the most important wood stove and fireplace manufacturers in North America, congratulates you on y

19 FIGURE 2.2.2 (B) Factory Built Thimble

20 FIGURE 2.2.2 (C) Brick Thimble

212.3 CHIMNEY CONNECTOR Your chimney connector (commonly called stove pipe) and chimney must have the same diameter as the stove’s exhaust outlet. T

22 FIGURE 2.3 (A) Connecting Sections 1/4" RISE PER FOOT FIGURE 2.3 (B) Minimum Slope

23Avoid 90 degree eblows We recommend that you use two 45 degree elbows instead

242.4 DRAFT Your E.P.A Enerzone stove’s performance will be optimised if it is installed with a chimney (flue) system that provides an adequate dra

252.6 THE ADVANTAGE OF USING A BLOWER (FAN) A blower is installed at the back of your E.P.A Enerzone stove model Solution 3.4. The blower should b

26SECTION 3.0 OPERATION Keep these instructions for future reference. WARNING: • ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED I

273.1 SAFETY INFORMATION • These stoves are designed for safe operation WHEN BURNING WOOD ONLY. Altering or modifying the unit or installation w

28• Although the ceramic glass is extremely durable under any normal use, a few precautions are required. Do not attempt to push logs further into t

2TABLE OF CONTENTS 1.1 GENERAL INSTALLATION ...

29 Wood species Energy yield (millions of BTU/cord) High energy yield Oak 29 Sugar Maple 28 Beech 26 Yellow birch 25 Ash 24 Elm 23 Medium energy y

303.2.2 Simple wood moisture test Add one large piece of wood to the top of an established fire. If it starts to burn on three sides within one mi

31Intensity Draft Setting Low Push Control completely to end of travel toward the left. Medium Low Pull Control to the right by 3/8” from closed p

32long enough to achieve a hot fire. The wood should be placed with air in between individual pieces. Use a poker to make an air channel in the embe

33 SECTION 4.0 MAINTENANCE 4.1 CLEANING AND PAINTING YOUR STOVE Clean the stove frequently so that soot, ash, and creosote do not accumulate. Do

34 Glass specifications: Robax 5mm with dimensions of 17 3/32" x 9 13/16" DOOR FRAMEGLASS RETAINERGLASSGLASSFRAMEDOOROVERLAY

35• Push the ashes through the hole and leave an ash bed of approximately 1” deep on the firebox bottom to help maintain a hot ember bed. • Clear

364.6 BAFFLE INSTALLATION 4.6.1 Baffle installation and brick layout for Solution 3.4 model All firebrick and ceramic wool baffles must be pr

374.7 SECONDARY AIR TUBE REPLACEMENT (see Figure 4.11) Figure 4.7.1 – Secondary air tube replacement

38 SECTION 5.0 SPECIFICATIONS 5.1 SOLUTION 3.4 Fuel Type Cordwood Test Standards ULC S627 (CSA B366.2) & UL 1482 residential.

3SECTION 5.0 SPECIFICATIONS ... 38 5.1 SOLUT

39ENERZONE LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. This

4SECTION 1.0 - INSTALLATION When installed and operated as described in these instructions, the E.P.A Enerzone wood stove is suitable for use as a

51.1.1 Installation of the decorative u-shaped inserts Your freestanding Enerzone wood stove is equipped with decorative u-shaped inserts. See tabl

6 1.2 POSITIONING THE STOVE It is very important to position the wood stove in an area that will favour the most efficient heat distribution throu

7 Figure 1.3 Clearances to combustible materials

81.3.1 Reduced clearances You may decrease the clearances by installing heat radiation shields between the walls or the ceiling and the stove. Th